Zhao Jinlong*,Zhang Huayun.Effect of sandblasting on corrosion resistance of 45 # steel surface[J].Plating & Finishing,2023,(3):95-100.[doi:10.3969/j.issn.1001-3849.2023.03.014]
喷砂对45#钢表面耐蚀性的影响
- Title:
- Effect of sandblasting on corrosion resistance of 45 # steel surface
- Keywords:
- sandblasting ; mesh number ; plating ; corrosion resistance
- 分类号:
- TQ153
- 文献标志码:
- A
- 摘要:
- 选取 45# 钢材料进行了喷砂试验,试样分别采用 40 目、 150 目、 220 目、 W40 砂粒进行喷砂处理,喷砂后进行镀锌、镀镉处理,最后进行中性盐雾试验。研究了不同砂粒目数对基体表面的损伤及耐蚀性的影响。结果表明,喷砂在增加试样表面积的同时,会对基体表面造成不同程度的损伤,砂粒粒径越大对试样表面的损伤越严重,表面粗糙度值越大,耐蚀性越差。采用不同目数砂粒喷砂的试样经镀锌处理, 48 h 盐雾试验后试样表面均出现不同程度的腐蚀现象;而经镀镉处理后, 360 h 盐雾试验后试样未出现腐蚀现象。
- Abstract:
- : 45 # steel material was selected for sandblasting test. The samples were sandblasted with 40 mesh , 150 mesh , 220 mesh and W40 grit respectively , zinc and cadmium platings were carried out after sandblasting , and neutral salt spray corrosion test was carried out finally. The influence of different grit sizes on the damage and corrosion resistance of the substrate surface after sandblasting was studied. The results show that while sandblasting increasing the surface area of the sample , it will cause different degrees of damage to the substrate surface , the larger the sand particles are , the more serious damage to the sample surface and the worse corrosion resistance of the surface were produced. After sandblasting with four different mesh sizes and 48 h of salt spray test , the sample surface of zinc plating shows different degrees of corrosion , while cadmium plating with sandblasting shows no corrosion after 360 h of salt spray test.
参考文献/References:
[1] 汪余博 , 戴京涛 , 苏洪波 , 等 . 喷砂工艺对粘接耐久性能的影响及评价研究 [J]. 中国胶粘剂 , 2021, 30(5): 60-64.
[2] 李忠敏 , 薛磊 , 杨海波 . 喷砂工艺在船舶涂装后阶段生产中的应用 [J]. 江苏科技信息 , 2021, 30:42-47.
[3] 刘耀洲 . 喷砂 ( 抛丸 ) 工艺对建筑钢结构表面的影响 [J]. 中外建筑 , 2009, 5: 243-244.
[4] 都昌林 , 易春龙 . 钢桥面无尘喷砂除锈设备及施工工艺 [J]. 表面技术 , 2004, 2: 46-47.
[5] 龙袁 , 郝玉林 , 刁鑫林 , 等 . 喷砂工艺对 22MnB5 热成形钢涂装性能的影响 [J]. 电镀与涂饰 , 2022, 41(8): 561-565.
[6] Rudawska A, Danczak I, Muller, et al. The effect of sandblasting on surface properties for adhesion[J]. International Journal of Adhesion and Adhesives, 2016, 70: 176-190.
[7] 田旭 , 李顺新 , 裴锋 , 等 . Q235 钢和镀锌钢在南昌大气环境中的腐蚀行为 [J]. 热加工技术 , 2022, 51(6): 32-38.
[8] 魏英华 , 袁晓光 , 安敏 , 等 . 喷砂处理对 8Cr4Mo4V 钢表面状态的影响 [J]. 航空制造技术 , 2019, 62(21): 40-46.
[9] 李红艳 . 喷砂粒径对农业机械涂装膜层性能的影响 [J]. 电镀与精饰 , 2019, 41(7): 36-37.
[10] 肖刚 , 胡秋 , 周立 . 铝型材表面喷砂预处理及其对阳极氧化膜性能的影响 [J]. 铝合金加工技术 , 2001, 29(8): 38-40.
[11] 缪小吉 , 宋璐 , 卢阳阳 , 等 , 喷砂预处理对 20CrMnMo 钢气体渗碳效率及渗层特性的影响 [J]. 材料热处理学报 , 2021, 42(5): 124-128.
[12] 刘栓 , 孙虎元 , 范汇吉 , 等 . 镀锌钢腐蚀行为的研究进展 . 材料保护 [J], 2012, 12: 42-45.
[13] 陈亚 . 现代实用电镀技术 [M]. 北京 : 国防工业出版社 , 2004: 239-240.
[14] 肖革 , 杨晓波 , 向可友 , 等 . 电镀锌及热浸镀锌钢板磷化工艺新进展 [J]. 电镀与精饰 , 2021, 43(9): 31-32.
[15] 陈心欣 , 付益平 , 刘秀珍 , 等 . 电镀锌工艺盐雾试验研究 [J]. 环境技术 , 2021( 增刊 ): 33-36.
[16] 唐春华 . 锌及锌合金板材的磷化工艺 [J]. 材料保护 , 2000, 33(11): 26-35.
[17] 唐春华 . 金属表面磷化技术 [M]. 北京 : 化学工业出版社 , 2011: 3-4.
[18] 吴悔 , 吴长军 , 刘亚 , 等 . 表面预氧化温度对球墨铸铁热浸镀锌层组织的影响 [J]. 材料保护 , 2022, 55(3): 7-13.
[19] 杨志业 , 胡遐林 , 王进军 , 等 . 民用飞机镀锌镍工艺研究 [J]. 材料保护 , 2022, 55(3): 98-101.
[20] 毛喆 , 胡剑锋 , 黄红武 , 等 . 对镀镉层防护不当的常见现象及防控措施 [J]. 电镀与精饰 , 2021, 43(2): 47-50.
[21] 万冰华 , 费敬银 , 王磊 , 等 . 钢铁基体电镀锌合金的研究现状 [J]. 电镀与精饰 , 2010, 32(6): 19-20.
[22] 章葆澄 . 电镀工艺学 [M]. 北京 : 北京航空航天大学出版社 , 1993: 77.
相似文献/References:
[1]程宝改,李宝增,谢美芳,等.喷砂对水性涂装漆膜形貌与性能的影响[J].电镀与精饰,2019,(7):31.[doi:10.3969/j.issn.1001-3849.2019.07.007]
CHENG Baogai,LI Baozeng,XIE Meifang,et al.Influence of Sandblasting on Morphology and Adhesion of Water-Borne Film[J].Plating & Finishing,2019,(3):31.[doi:10.3969/j.issn.1001-3849.2019.07.007]
[2]王朝琳*,宋斌,刘娟,等.直升机桨叶包片胶接前激光毛化处理的有效性研究[J].电镀与精饰,2021,(12):29.[doi:10.3969/j.issn.1001-3849.2021.12.006]
WANG Chaolin*,SONG Bin,LIU Juan,et al.The Effectiveness of Laser Texturing Technology in Surface Treatment of the Bonding Quality of Helicopter Slurry Pack[J].Plating & Finishing,2021,(3):29.[doi:10.3969/j.issn.1001-3849.2021.12.006]
[3]陈婧*.粗糙度对水性涂料涂装膜层结合力的影响?/div>[J].电镀与精饰,2022,(12):25.[doi:10.3969/j.issn.1001-3849.2022.12.004]
CHEN Jing *.Effect of Roughness on Adhesion of Waterborne Coatings[J].Plating & Finishing,2022,(3):25.[doi:10.3969/j.issn.1001-3849.2022.12.004]
备注/Memo
收稿日期: 2022-12-31 修回日期: 2023-01-27 作者简介: 赵金龙( 1989 -),男,本科,工程师,主要从事金属材料热处理专业, e-mail : 13938814518@139.com