PDF下载 分享
[1]陈婧*.粗糙度对水性涂料涂装膜层结合力的影响?/div>[J].电镀与精饰,2022,(12):25-31.[doi:10.3969/j.issn.1001-3849.2022.12.004]
　CHEN Jing *.Effect of Roughness on Adhesion of Waterborne Coatings[J].Plating & Finishing,2022,(12):25-31.[doi:10.3969/j.issn.1001-3849.2022.12.004]
点击复制

粗糙度对水性涂料涂装膜层结合力的影响?/div>

《电镀与精饰》[ISSN:1001-3849/CN:12-1096/TG] 卷: 期数: 2022年12 页码: 25-31 栏目: 出版日期: 2022-12-15
Title:
Effect of Roughness on Adhesion of Waterborne Coatings
作者:
陈婧*
（贵州交通职业技术学院 汽车工程系， 贵州 贵阳 550008）
Author(s):
CHEN Jing *
（Department of Automotive Engineering， Guizhou Jiaotong Polytechnics， Guiyang 550008， China）

关键词:
喷砂; 水性涂料; 附着力; 耐腐蚀
Keywords:
sandblasting ;  waterborne coating ;  adhesion ;  corrosion resistance
分类号:
TQ638
DOI:
10.3969/j.issn.1001-3849.2022.12.004
文献标志码:
A
摘要:
水性涂料涂装作为腐蚀保护涂层具有清洁环保的优势，符合国家环境保护的大趋势，但是与溶剂型涂装技术比较，其漆膜附着力有限导致耐腐蚀性能稍差，成为其广泛推广应用的障碍。为获取性能优良的涂层，本文采用不同粒度的砂粒进行喷砂作为前处理工艺，选用水性涂料作为涂装防护层，并进行了试样变形量、粗糙度、漆膜厚度与耐蚀性能测试。结果表明：砂粒粒径较大，获得的粗糙度比较大，涂层与基体结合情况良好，附着力比较大，耐腐蚀性能良好。
Abstract:
： As a corrosion protection ， waterborne coating has the advantages of clean and environmental protection ， which is in line with the general trend of national environmental protection. However ， compared with solvent coating technology ， its film adhesion is limited ， leading to its slightly poor corrosion resistance ， which has become an obstacle for its widespread application. In order to obtain the coating with good performance ， sand particles of different sizes were used for sand blasting as the pretreatment process ， and waterborne coating was selected as the coating protective layer. The deformation ， roughness ， film thickness and corrosion resistance of the sample were tested. The results show that the sand particle size is large ， the roughness is large ， the coating and the matrix are well bonded ， the adhesion is large ， and the corrosion resistance is good.

参考文献/References:



[1] 曾宪光 , 龚敏 , 刘朝辉 , 等 . 水性聚氨酯涂料的研究现状 [J]. 电镀与涂饰 , 2018, 37(22): 1060-1067.

[2] 胡中 , 许飞 , 庄振宇 , 等 . 基于自增稠型羟基丙烯酸乳液的水性珠光涂料的制备 [J]. 涂料工业 , 2017, 47(5): 11-16.

[3] 张爱黎 , 田坤 , 常彩彩 , 等 . 改性环氧丙烯酸水性防腐涂料制备研究 [J]. 电镀与精饰 , 2015, 37(11): 15-19.

[4] 熊俊良 , 周玉龙 . 电镀镉层斑点故障原因及解决措施 [J]. 电镀与精饰 , 2020, 42(4): 41-42.

[5] 迟长云 . 表面粗糙度对传动轴静电粉末喷涂涂层性能的影响 [J]. 腐蚀与防护 , 2019, (5): 379-382+390.

[6] 李红艳 , 李增权 , 徐明磊 . 农用机械便利型涂装修复技术 [J]. 电镀与精饰 , 2018, 40(12): 33-37.

相似文献/References:

[1]孙海静,徐佳新,姚宇煊,等.水性有机硅改性环氧丙烯酸树脂的制备及性能研究[J].电镀与精饰,2020,(3):18.[doi:10.3969/j.issn.1001-3849.2020.03.004]
　SUN Haijing,XU Jiaxin,YAO Yuxuan,et al.Preparation and Study on Water-based Silicone Modified Epoxy-Acrylate Resin[J].Plating & Finishing,2020,(12):18.[doi:10.3969/j.issn.1001-3849.2020.03.004]
[2]王朝琳*,宋斌,刘娟,等.直升机桨叶包片胶接前激光毛化处理的有效性研究[J].电镀与精饰,2021,(12):29.[doi:10.3969/j.issn.1001-3849.2021.12.006]
　WANG Chaolin*,SONG Bin,LIU Juan,et al.The Effectiveness of Laser Texturing Technology in Surface Treatment of the Bonding Quality of Helicopter Slurry Pack[J].Plating & Finishing,2021,(12):29.[doi:10.3969/j.issn.1001-3849.2021.12.006]
[3]赵金龙*,张华云. 喷砂对45#钢表面耐蚀性的影响 [J].电镀与精饰,2023,(3):95.[doi:10.3969/j.issn.1001-3849.2023.03.014]
　Zhao Jinlong*,Zhang Huayun.Effect of sandblasting on corrosion resistance of 45 # steel surface[J].Plating & Finishing,2023,(12):95.[doi:10.3969/j.issn.1001-3849.2023.03.014]
[4]程宝改,李宝增,谢美芳,等.喷砂对水性涂装漆膜形貌与性能的影响[J].电镀与精饰,2019,(7):31.[doi:10.3969/j.issn.1001-3849.2019.07.007]
　CHENG Baogai,LI Baozeng,XIE Meifang,et al.Influence of Sandblasting on Morphology and Adhesion of Water-Borne Film[J].Plating & Finishing,2019,(12):31.[doi:10.3969/j.issn.1001-3849.2019.07.007]

备注/Memo

收稿日期： 2020-09-16 修回日期： 2020-09-27 作者简介： 陈婧（ 1967 —），女，本科，副教授， email ： chenjingxls@163.com?/html>

更新日期/Last Update: 2022-12-16