[1]尚洪帅,邹松华,王帅东,等.化铣保护胶自动浸涂影响因素分析及研究[J].电镀与精饰,2019,(1):1-4.[doi:10.3969/j.issn.1001-3849.2019.01.001]
　SHANG Hongshuai,ZOU Songhua,WAGN Shuaidong,et al.Analysis of Influencing Factors of Chemical MillingProtective Adhesive Automatic Dipping[J].Plating & Finishing,2019,(1):1-4.[doi:10.3969/j.issn.1001-3849.2019.01.001]
点击复制

化铣保护胶自动浸涂影响因素分析及研究()

《电镀与精饰》[ISSN:1001-3849/CN:12-1096/TG]

卷:
期数:
2019年1
页码:
1-4
栏目:
出版日期:
2019-01-07

文章信息/Info

Title:
Analysis of Influencing Factors of Chemical Milling Protective Adhesive Automatic Dipping
作者:
尚洪帅; 邹松华; 王帅东; 徐方强; 张子炫; 郭志辉
天津航天长征火箭制造有限公司，天津 300462
Author(s):
SHANG Hongshuai;  ZOU Songhua;  WAGN Shuaidong;  XU Fangqiang;  ZHANG Zixuan;  GUO Zhihui
Tianjin Long March Launch Vehicle Manufacturing Co. Ltd, Tianjin 300462, China
关键词:
保护胶; 自动浸涂; 影响因素
Keywords:
protective adhesive;  automatic dipping;  influencing factor
分类号:
TQ637
DOI:
10.3969/j.issn.1001-3849.2019.01.001
文献标志码:
A
摘要:
本文对化铣保护胶自动浸涂过程中的胶液温度、胶液黏度、浸胶停留时间、浸胶次数等影响因素进行了分析和研究。结果表明，温度过高或过低均影响胶液流动性，不利于胶层厚度均匀性要求；保证总厚度情况下，浸胶次数越少，越利于胶层均匀性控制；胶液黏度在45~55 s时，可以有效避免胶层质量缺陷；工件在胶液的停留时间对胶层质量稳定性影响不明显。
Abstract:
Influencing factors in automatic dipping process of protective adhesive for chemical milling, such as adhesive temperature, adhesive viscosity, dipping residence time, dipping times and so on, were analyzed and researched in this paper. The results show that excessive or low temperature will affect the fluidity of the adhesive, which is bad for the uniformity of the adhesive layer thickness. When the total thickness is kept constant, the less the dipping times are, the better the control of the uniformity of the adhesive layer is. When adhesive viscosity was 45－55 s, coating defects could be avoided. Effect of dipping residence time on the stability of adhesive quality is not obvious.

参考文献/References:

［1］李善芝, 柳丕, 李文光. 运载火箭贮箱壁板化铣旋转设备的设计[J]. 航天制造技术, 2010(1): 58-60.
［2］王辉, 杜兴盛, 杨俊坤. 钛合金化铣尖边化学法去除工艺研究[J]. 电镀与精饰, 2018, 40(1): 35-39.
［3］张震, 李丽, 王颖, 李在兴, 荣海宏. 环保型可剥性保护涂料的研制[J]. 电镀与涂饰, 2011, 30(4): 68-70.
［4］王帅, 于钦泰, 杜丽梅. 环保型水基化铣可剥胶与溶剂型产品在航天铝合金材料化铣加工中的性能对比研究[J]. 云南化工, 2012, 39(1): 9-12.
［5］王颖, 周春艳, 张震. 环境友好型化学铣切保护涂料的研制[J]. 现代涂料与涂装, 2008, 11(7): 30-31.

备注/Memo

备注/Memo:
收稿日期： 2018-09-29
修回日期： 2018-10-15
更新日期/Last Update: 2019-01-16