Lu Yajuan *,Li Xiaozheng,Ma Yingchun,et al.Reason analysis of hard anodic oxide film falling off caused by a discharge accident[J].Plating & Finishing,2023,(1):92-97.[doi:10.3969/j.issn.1001-3849.2023.01.014]
一例放电事故造成硬氧膜脱落的原因分析
- Title:
- Reason analysis of hard anodic oxide film falling off caused by a discharge accident
- Keywords:
- high voltage switch ; discharge ; oxide film falling off
- 分类号:
- TG17
- 文献标志码:
- A
- 摘要:
- 针对一起特高压开关放电事故中电连接硬质阳极氧化膜焚化、脱落的问题,采用现场环境分析、工艺加工模拟以及对于脱落前后的硬质阳极氧化膜的成分进行宏观和微观分析的方法进行研究。结果表明,此次硬质阳极氧化膜脱落及焚化的主要原因为:放电产生的电弧将气室内六氟化硫气体分解成强腐蚀性有毒气体,并释放出大量的热量,导致氧化膜出现裂纹。产生的气体通过裂纹渗入氧化膜底部,与氧化膜发生物理、化学反应,从而造成氧化膜的脱落与焚化,研究结果为今后分析此类问题提供了依据。
- Abstract:
- : Aiming at the problem of incineration and falling off of hard anodic oxide film of electrical connection in an ultra-high voltage switch discharge accident , the methods of on-site environmental analysis , process simulation and macro and micro analysis of the composition of hard anodic oxide film before and after falling off are used to study. The results show that the main reason for the falling off and incineration of the hard anodic oxide film is that the arc generated by the discharge decomposes the sulfur hexafluoride gas in the gas chamber into highly corrosive toxic gas and releases a large amount of heat , resulting in cracks in the oxide film. The generated gas penetrates into the bottom of the oxide film through the crack and reacts physically and chemically with the oxide film , resulting in the falling off and incineration of the oxide film. The research results provide a basis for the analysis of such problems in the future.
参考文献/References:
[1] 安百刚 , 张学元 , 宋诗哲 . LY12 铝合金在模拟酸雨溶液中的阻抗谱研究 [J]. 中国腐蚀与防护学报 , 2003, 23(3): 167-170.
[2] 韩克 , 欧忠文 , 蒲滕 . 铝及铝合金硬质阳极氧化的研究进展 [J]. 表面技术 , 2011, 40(5): 92-96.
[3] 王栋栋 . 纯铝微弧氧化膜生长机制及耐蚀性能研究 [D]. 秦皇岛 : 燕山大学 , 2021.
[4] 曹金晖 . 高性能铝基阳极膜层的制备及其微观结构演化机理 [D]. 长沙 : 湖南大学 , 2018.
[5] 赵旭辉 , 左禹 , 赵景茂 . 几种封闭方法处理后铝阳极氧化膜的耐蚀性比较 [J]. 腐蚀与防护 , 2006, 27(8): 400-403.
[6] 李素琴 , 段绍范 , 段晓楠 . 铝合金脉冲硬质阳极氧化工艺与膜层性能的研究 [J]. 材料保护 , 1994, 27(3): 6-9.
[7] 王艳芝 . 铝及其合金阳极氧化技术研究的进展 [J]. 材料保护 , 2001, 34(9): 22-23.
[8] 姚素薇 , 孔亚西 , 张璐 . 高度有序多孔阳极氧化铝膜形成机理的探讨 [C]//. 2004 年全国电子电镀学术研讨会论文集 . 2004: 122-125.
[9] 李忠盛 , 吴护林 , 潘复生 . 氧化时间对 7A55 铝合金微弧氧化膜的影响 [J]. 航空材料学报 , 2009, 29(3): 26-29.
[10] 周育红 , 韩喜江 , 周德瑞 . 铝及铝合金阳极氧化膜的封闭技术 [J]. 哈尔滨工业大学学报 , 2003(11): 1325-1327, 1338.
[11] 肖作栋 , 邹群 , 黄清安 . 铝合金阳极氧化前处理工艺的改进 [J]. 材料保护 , 2004(2): 28-29, 64.
[12] 李兴旺 , 刘军 , 刘梦娜 . 一起气体绝缘金属封闭开关设备悬浮放电缺陷分析 [J]. 高压电器 , 2015, 51(10): 205-208.
[13] 司文荣 , 李军浩 , 袁鹏 . 气体绝缘组合电器多局部放电源的检测与识别 [J]. 中国电机工程学报 , 2009, 29(16): 119-126.
[14] 陈安明 , 杨洋 , 黄文龙 , 等 . 基于 SF 6 分解产物的 GIS 放电故障诊断分析 [J]. 绝缘材料 , 2013, 46(2): 83-85.
[15] 朱峰 , 林百志 , 郁光 , 等 . 气相色谱法在六氟化硫制备中的应用 [J]. 低温与特气 , 2021, 39(1): 38-46.
[16] 马志瀛 , 陈晓宁 , 徐黎明 , 等 . 超高压 SF 6 断路器的智能操作 [J]. 中国电机工程学报 , 1999(7): 12-14, 72.
[17] 王昌钧 . SF 6 高压断路器机械参量在线监测系统 [J]. 电网技术 , 1999(7): 34-37.
[18] 徐捷 . 检测六氟化硫气体分解产物诊断开关故障情况 [J]. 电世界 , 2015, 56(4): 28-29.
[19] 陈爽 . 提高铝合金阳极氧化膜在高温下的抗开裂性能研究 [D]. 北京 : 北京化工大学 , 2009.
[20] 马月辉 . 铝型材阳极氧化膜破裂原因及预防措施 [J]. 轻合金加工技术 , 2002(6): 47-48.
相似文献/References:
[1]王香玉*,雪金海,谢美芳,等.四种银镀层的制备与抗变色性能对比[J].电镀与精饰,2020,(7):12.[doi:10.3969/j.issn.1001-3849.2020.07.0030]
WANG Xiangyu*,XUE Jinhai,XIE Meifang,et al.Electrodeposition Preparation and Comparison of Anti-tarnish Properties of Four Kinds of Coatings[J].Plating & Finishing,2020,(1):12.[doi:10.3969/j.issn.1001-3849.2020.07.0030]
备注/Memo
收稿日期: 2022-01-20 修回日期: 2022-05-17 作者简介: 路亚娟( 1982 ―),女,本科,高级工程师, email : luyajuan0512@163.com?/html>