Zhang Yiying,Zhang Liuyan *,Han Zhaokang,et al.Study on the wear characteristics of Al-Ni-xCr composite coating prepared by low pressure cold spraying[J].Plating & Finishing,2024,(5):36-43.[doi:10.3969/j.issn.1001-3849.2024.05.005]
低压冷喷涂制备Al-Ni-xCr复合涂层及其磨损特性研究
- Title:
- Study on the wear characteristics of Al-Ni-xCr composite coating prepared by low pressure cold spraying
- 关键词:
- Al-Ni-Cr 复合涂层; 冷喷涂; 摩擦系数; 极化行为
- 分类号:
- TH117.1
- 文献标志码:
- A
- 摘要:
- 防腐性能较好的铝基涂层存在耐磨性不足的问题。本文设计了 Ni 粉和 Cr 粉复合沉积的方法来改善涂层的耐磨性。采用低压冷喷涂技术，制备了一系列 Cr 含量不同的 Al-Ni- x Cr 复合涂层。通过金相、扫描电镜及 X 射线衍射等方法分析了复合涂层的微观形貌和成分。采用显微硬度计和磨损仪测试了涂层的显微硬度和磨损曲线，结合磨痕形貌分析了复合涂层的磨损机理。研究得出：低压冷喷涂可实现 Al 、 Cr 、 Ni 三种金属粉的共沉积，并获得致密、均匀的 Al-Ni- x Cr 复合涂层。枝晶状 Ni 粉沉积率较高， Cr 粉沉积率较低。含 70 wt . %Cr 的混粉涂层中， Cr 含量约为 31 wt.% 。硬质颗粒 Cr 同时起到夯实涂层的作用，随着 Cr 含量增加， Al-Ni- x Cr 复合涂层的致密性提高。 Al-Ni- x Cr 复合涂层的耐磨性能主要来自于 Cr 而非 Ni ，且与 Cr 含量有关。 Al-Ni-70Cr 复合涂层耐磨性最佳，磨损率仅为 Al 涂层的 1/2 。其优异的耐磨性归因于摩擦界面形成了稳定的、较硬的、含 Cr 量较高的复合氧化膜，抑制了磨损过程。
- Abstract:
- ： The Al-based coating has well corrosion resistance ， but its wear resistance is poor. In this paper ， mixing Ni and Cr powders was designed to improve the wear resistance of the Al-based coating. A series of Al-Ni- x Cr composite coatings with different Cr content were prepared by low pressure cold spraying. Their micro-morphology and composition were analyzed by means of metallography ， scanning electron microscopy and X-ray diffraction. Their microhardness and wear curve were measured by microhardness tester and wear meter. Their wear mechanism was analyzed according to the microscopic characteristics. The results show that the low pressure cold spraying can achieve the co-deposition of Al ， Cr and Ni metal powder. The Al-Ni- x Cr composite coating is dense and uniform. Dendrite Ni powder has a higher deposition rate ， while Cr powder shows a lower deposition rate. The Cr content in Al-Ni-70Cr coating is about 31 wt.%. With the increase of Cr content ， the densification of Al-Ni- x Cr composite coating increases. The wear resistance of Al-Ni- x Cr composite coating is mainly related to Cr content rather than Ni. Al-Ni-70Cr composite coating has the best wear resistance ， and its wear rate is only 1/2 of that of Al coating. Its excellent wear resistance is attributed to the formation of a stable hard and high Cr-containing composite oxide film at the friction interface ， which inhibits the wear process.
参考文献/References:
[1] 潘波涛 , 李园园 , 王锦霞 , 等 . 铝防护涂层制备方法的研究进展 [J]. 材料保护 , 2022, 55(10): 171-179.
[2] 钟厉 , 王昭银 , 张华东 . 冷喷涂沉积机理及其装备的研究进展 [J]. 表面技术 , 2015, 44(4): 15-20.
[3] 任子阳 , 汤嘉昊 , 殷世铜 , 等 . 冷喷涂制备铝基涂层研究进展及应用现状分析 [J]. 电镀与精饰 , 2023, 45(8): 74-80.
[4] Spencer K, Fabijanic D M, Zhang M X. The use of Al-Al 2 O 3 cold spray coatings to improve the surface properties of magnesium alloys[J]. Surface & Coatings Technology, 2009, 204(3): 336-344.
[5] 陈金雄 , 王群 , 罗丝丝 , 等 . AZ31 镁合金冷喷涂 Al-Al 2 O 3 复合涂层组织及性能 [J]. 中国有色金属学报 , 2018, 28(9): 1720-1729.
[6] Cong D, Li Z, He Q, et al. Wear behavior of corroded Al-Al 2 O 3 composite coatings prepared by cold spray[J]. Surface & Coatings Technology, 2017, 326: 247-254.
[7] 徐鲁杰 , 韩超 , 黄国胜 . 不同 B 4 C 含量对冷喷涂 Al/B4C 复合涂层防腐与耐磨性能的影响 [J]. 装备环境工程 , 2022, 19(8): 90-102.
[8] 邓碧欣 , 孙澄川 , 何超 , 等 . 冷喷涂 Al6061/SiC 复合涂层的制备及性能研究 [J]. 材料保护 , 2023, 56(11): 1-12.
[9] Loganathan A, Rengifo S, Hernandez A F, et al. Effect of nanodiamond reinforcement and heat-treatment on microstructure, mechanical and tribological properties of cold sprayed aluminum coating[J]. Surface & Coatings Technology, 2021, 412: 127037.
[10] Wu H, Zhang Y, Shao L, et al. Tribological behavior of graphene anchored Mg-Al layered double hydroxide film on Mg alloy pre-sprayed Al coating[J]. Applied Surface Science, 2020, 530: 146536.
[11] 李文亚 , 张正茂 , 徐雅欣 , 等 . 冷喷涂 Ni 及镍基复合涂层研究进展 [J]. 金属学报 , 2022, 58(1): 1-16.
[12] 李旭 , 王强 , 牛文娟 , 等 . 热处理对冷喷涂 Al-Ni 沉积体组织和力学性能的影响 [J]. 稀有金属 , 2020, 44(11): 1153-1162.
[13] 刘志凯 , 沈耿哲 , 刘灿森 , 等 . 低压冷喷涂热处理复合处理制备 Ni 2 Al 3 金属间化合物涂层及其滑动磨损特性研究 [J]. 材料保护 , 2023, 56(3): 1-5.
[14] Bala N, Singh H, Prakash S. Accelerated hot corrosion studies of cold spray Ni?50Cr coating on boiler steels[J]. Materials & Design, 2010, 31(1): 244-253.
[15] 吴畏 . 热加工对低压冷喷涂 7075 铝合金复合材料组织与性能的影响研究 [D]. 广州 : 广东工业大学材料与能源学院 , 2021.
[16] 杨景文 , 李文亚 , 邢词皓 , 等 . 冷喷涂铜涂层研究进展 [J]. 材料保护 , 2022, 55(1): 58-70.
[17] 钟厉 , 王昭银 , 张华东 . 冷喷涂沉积机理及其装备的研究进展 [J]. 表面技术 , 2015, 44(4): 15-19.
[18] Koivuluoto H, Vuoristo P. Effect of powder type and composition on structure and mechanical properties of Cu+Al 2 O 3 coatings prepared by using low-pressure cold spray Process[J]. Journal of Thermal Spray Technology, 2010, 19(5): 1081-1092.
[19] 杨水梅 , 张留艳 , 詹浩芝 , 等 . 掺杂镍对镁合金表面冷喷涂锌基涂层性能的影响 [J]. 表面技术 , 2019, 48(5): 217-224.
[20] Koivuluoto H, Lagerbom J, Vuoristo P. Microstructural studies of cold sprayed copper, nickel, and nickel-30% copper coatings[J]. Journal of Thermal Spray Technology, 2007, 16(4): 488-497.
[21] 杨康 , 李文亚 . 冷喷涂 Cu/Ni/Al 复合涂层内部粒子间的结合特性研究 [J]. 焊管 , 2018, 41(1): 15-19.
相似文献/References:
[1]曹 棋,黄从运,黄国胜*,等.冷喷涂和等离子喷涂Fe基非晶涂层特征对比研究[J].电镀与精饰,2020,(5):1.[doi:10.3969/j.issn.1001-3849.2020.05.0010]
CAO Qi,HUANG Congyun,HUANG Guosheng*,et al.Comparative Study on the Characteristics of Fe-Based Amorphous Coatings for Cold Spraying and Plasma Spraying[J].Plating & Finishing,2020,(5):1.[doi:10.3969/j.issn.1001-3849.2020.05.0010]
[2]任子阳,汤嘉昊,殷世铜,等. 冷喷涂制备铝基涂层研究进展及应用现状分析 [J].电镀与精饰,2023,(8):74.[doi:10.3969/j.issn.1001-3849.2023.08.012]
Ren Ziyang,Tang Jiahao,Yin Shitong,et al.Research progress and application status analysis of aluminum-based coatings prepared by cold spraying[J].Plating & Finishing,2023,(5):74.[doi:10.3969/j.issn.1001-3849.2023.08.012]
备注/Memo
收稿日期： 2023-12-12 修回日期： 2024-01-25 作者简介： 张怡颖（ 2000 —），女，研究生，研究方向：表面工程， email ： 1041583198@qq.com * 通信作者： 张留艳（ 1983 —），女，博士，副教授，研究方向：表面工程， email ： zlyjust@gdut.edu.cn 基金项目： 广东省基础与应用基础研究基金（ No. 2022A1515240004 ）；广州市科技计划项目（ No. 2023A04J0270 ）?/html>